A practical reference on Stationary phase: what it is, how it behaves, what the literature reports, and where the honest uncertainties sit.
This page was last updated on 2026-02-21 and is reviewed periodically as new material appears.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
Laboratories apply HPLC testing across pharmaceutical, food, environmental, and industrial chemistry. The method can measure active ingredients, impurities, additives, preservatives, and degradation products. Sample preparation often includes dilution, filtration, and sometimes extraction or derivatization. The choice of column, mobile phase, pH, temperature, and detector depends on the analytes and matrix. Results are compared with reference standards to assign identity and concentration. Method suitability is judged by resolution, precision, and accuracy.
HPLC testing is not a single fixed procedure; it is a family of separation modes. Reversed-phase, normal-phase, ion-exchange, size-exclusion, and affinity chromatography each suit different analyte properties. Reversed-phase methods dominate because they handle many neutral and moderately polar compounds. Detection can be optical, electrochemical, or mass spectrometric, and the detector dictates what information is available. Coupling with mass spectrometry increases selectivity and enables identification when standards are unavailable. The technique cannot separate every mixture without adjustment.
HPLC testing is an analytical technique used to separate, identify, and quantify components in a liquid sample. It relies on a pressurized mobile phase that carries the sample through a column packed with stationary phase. Different compounds travel at different rates because of interactions with the stationary and mobile phases. The resulting signal versus time is a chromatogram. Peak position indicates identity under specified conditions, while peak area or height relates to amount.
| Property | Value | Notes |
|---|---|---|
| Retention time RSD | ≤1% for five replicate injections | Typical criterion; method-specific limits apply. |
| Resolution | ≥1.5 between critical pair | Baseline separation is generally desired. |
| Tailing factor | ≤2.0 | Measures peak symmetry. |
| Theoretical plates | ≥2000 per column | Method-dependent; higher values indicate greater efficiency. |
| Peak area RSD | ≤2% for replicate injections | Reflects autosampler and detector precision. |
Data handling and documentation are central to HPLC quality control. Electronic systems should have audit trails that record changes to methods, sequences, and results. Integration parameters, such as peak baseline and threshold, can affect reported areas and must be defined in advance. Out-of-specification results trigger a structured investigation that may include reanalysis, instrument checks, and review of sample preparation. Regulatory inspections often examine raw data, audit trails, and training records to verify that reported results are traceable and reliable.
Method validation establishes that an HPLC procedure is suitable for its intended use. Key parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Accuracy measures agreement with a true or accepted value, while precision describes repeatability and intermediate precision. Specificity confirms that the method measures the analyte without interference from impurities, degradants, or excipients. Validation is documented in a protocol and report, and acceptance criteria are set before experiments begin. Regulatory guidance varies by region, but the general principles are widely harmonized.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
Acetyl phosphate (AcP), a precursor to ATP, can readily be synthesized at modest yields from thioacetate in pH 7 and 20 °C and pH 8 and 50 °C, although acetyl phosphate is less stable in warmer temperatures and alkaline conditions than in cooler and acidic to neutral conditions. It is unable to promote polymerization of ribonucleotides and amino acids and was only capable of phosphorylation of organic compounds. It was shown that it can promote aggregation and stabilization of AMP in the presence of Na+, aggregation of nucleotides could promote polymerization above 75 °C in the absence of Na+. It is possible that polymerization promoted by AcP could occur at mineral surfaces. It was shown that ADP can only be phosphorylated to ATP by AcP and other nucleoside triphosphates were not phosphorylated by AcP. This might explain why all lifeforms use ATP to drive biochemical reactions.
In the anterior pituitary, the term "acidophil" is used to describe two different types of cells which stain well with acidic dyes. Somatotrophs, which secrete growth hormone (a peptide hormone) Lactotrophs, which secrete prolactin (a peptide hormone) When using standard staining techniques, they cannot be distinguished from each other (though they can be distinguished from basophils and chromophobes), and are therefore identified simply as "acidophils". Eosinophilic Acidophile (histology) Basophilic Chromophobe cell Melanotroph Chromophil Basophil cell Oxyphil cell Oxyphil cell (parathyroid) Pituitary gland Neuroendocrine cell
Antimicrobial peptides are produced by species across the tree of life, including: bacteria (e.g. bacteriocin, and many others) fungi (e.g. peptaibols, plectasin, and many others) cnidaria (e.g. hydramacin, aurelin) many from insects and arthropods (e.g. cecropin, attacin, melittin, mastoparan, drosomycin, thioester-containing protein 1) amphibia, frogs (magainin, dermaseptin, aurein, and others) birds (e.g. avian defensins) and mammals (e.g. cathelicidins, alpha- and beta-defensins, regIII peptides) Research has increased in recent years to develop artificially-engineered mimics of antimicrobial peptides such as SNAPPs, in part due to the prohibitive cost of producing naturally-derived AMPs. An example of this is the facially cationic peptide C18G, which was designed from the C-terminal domain of human platelet factor IV. Currently, the most widely used antimicrobial peptide is nisin; being the only FDA approved antimicrobial peptide, it is commonly used as an artificial preservative.
Polycondensation involves the formation of polymers through condensation reactions between different species, creating condensation polymers. With automated synthesis, General electric manufactured an approach for melt-polymerizations of BPA and diphenyl carbonate (DPC), using sodium hydroxide (NaOH) as the catalyst. Once the results were analyzed, it was shown that, by using an automated method of polymerization, the effect of varying the catalyst amount became more distinct and improved the reproducibility for the reaction. Furthermore, it demonstrated an increase within the homogeneity of the polymers in the microreactors.
Sources: en.wikipedia.org
Chromatin remodelers in the INO80 subfamily are made of multiple subunit complexes with split ATPase domains. The INO80 subfamily's protein domains are an N-terminus, two RuvB-like proteins (Rvb1 and Rvb2), and a C-terminus. The ATPase domain of the N-terminus functions in the identification of DNA damage and aids in the stability of telomeres. A long insertion in the ATPase domain is what recruits the Rvb1 and Rvb2 helicases. These helicases contribute to genome maintenance and are unique to the INO80 subfamily of chromatin remodeling complexes. This subfamily also contains an Arp4-actin complex that aids in stability of genes. The Arp5 subunit is required for ATPase function, binding to the DNA, and relocation of nucleosomes.
The removal of dead cells by neighboring phagocytic cells has been termed efferocytosis. Dying cells that undergo the final stages of apoptosis display apoptotic-cell associated molecular patterns (ACAMPs), such as phosphatidylserine on the outer leaflet of the cell membrane. Phosphatidylserine is normally found on the inner leaflet surface of the plasma membrane, but is redistributed during apoptosis to the extracellular surface by a protein known as scramblase. These molecules mark the cell for phagocytosis by cells possessing the appropriate receptors, such as macrophages. The removal of dying cells by phagocytes occurs in an orderly manner without eliciting an inflammatory response. During apoptosis cellular RNA and DNA are separated from each other and sorted to different apoptotic bodies; separation of RNA is initiated as nucleolar segregation.
P-glycoprotein (3.A.1.201.1) is a well-studied protein associated with multi-drug resistance. It belongs to the human ABCB (MDR/TAP) family and is also known as ABCB1 or MDR1 Pgp. MDR1 consists of a functional monomer with two transmembrane domains (TMD) and two nucleotide-binding domains (NBD). This protein can transport mainly cationic or electrically neutral substrates as well as a broad spectrum of amphiphilic substrates. The structure of the full-size ABCB1 monomer was obtained in the presence and absence of nucleotide using electron cryo crystallography. Without the nucleotide, the TMDs are approximately parallel and form a barrel surrounding a central pore, with the opening facing towards the extracellular side of the membrane and closed at the intracellular face. In the presence of the nonhydrolyzable ATP analog, AMP-PNP, the TMDs have a substantial reorganization with three clearly segregated domains. A central pore, which is enclosed between the TMDs, is slightly open towards the intracellular face with a gap between two domains allowing access of substrate from the lipid phase. Substantial repacking and possible rotation of the TM helices upon nucleotide binding suggests a helix rotation model for the transport mechanism.
ProIAPP consists of 67 amino acids, which follow a 22 amino acid signal peptide which is rapidly cleaved after translation of the 89 amino acid coding sequence. The human sequence (from N-terminus to C-terminus) is: (MGILKLQVFLIVLSVALNHLKA) TPIESHQVEKR^ KCNTATCATQRLANFLVHSSNNFGAILSSTNVGSNTYG^ KR^ NAVEVLKREPLNYLPL. The signal peptide is removed during translation of the protein and transport into the endoplasmic reticulum. Once inside the endoplasmic reticulum, a disulfide bond is formed between cysteine residues numbers 2 and 7. Later in the secretory pathway, the precursor undergoes additional proteolysis and posttranslational modification (indicated by ^). 11 amino acids are removed from the N-terminus by the enzyme proprotein convertase 2 (PC2) while 16 are removed from the C-terminus of the proIAPP molecule by proprotein convertase 1/3 (PC1/3). At the C-terminus Carboxypeptidase E then removes the terminal lysine and arginine residues. The terminal glycine amino acid that results from this cleavage allows the enzyme peptidylglycine alpha-amidating monooxygenase (PAM) to convert the terminal glycine to an amine group (releasing glycolate). After this step, the transformation from the precursor protein proIAPP to the biologically active IAPP (amylin) is complete (IAPP sequence: KCNTATCATQRLANFLVHSSNNFGAILSSTNVGSNTY-NH2).
The Society recognizes achievements and promotes academic research through four annual awards. The Biemann Medal and the John B. Fenn Award for a Distinguished Contribution in Mass Spectrometry both are awarded in recognition of singular achievements or contributions in fundamental or applied mass spectrometry, with the Biemann Medal being focused on individuals who are early in their careers. The Ronald A. Hites Award is awarded for outstanding original research demonstrated in papers published in the Journal of the American Society for Mass Spectrometry. The Research Awards are given to young scientists in mass spectrometry, based on the evaluation of their proposed research. The Fellows of ASMS are awarded to individuals in recognition for their scientific contribution to mass spectrometry and for their contribution to the ASMS community. Journal of the American Society for Mass Spectrometry Measuring Mass: From Positive Rays to Proteins The past presidents of ASMS are:
Sources: en.wikipedia.org
Peptide aptamers consist of one or more peptide loops of variable sequence displayed by a protein scaffold. Derivatives known as tadpoles, in which peptide aptamer "heads" are covalently linked to unique sequence double-stranded DNA "tails", allow quantification of scarce target molecules in mixtures by PCR (using, for example, the quantitative real-time polymerase chain reaction) of their DNA tails. The peptides that form the aptamer variable regions are synthesized as part of the same polypeptide chain as the scaffold and are constrained at their N and C termini by linkage to it. This double structural constraint decreases the diversity of the 3D structures that the variable regions can adopt, and this reduction in structural diversity lowers the entropic cost of molecular binding when interaction with the target causes the variable regions to adopt a uniform structure.
Extrapituitary prolactin is controlled by a superdistal promoter, located 5.8 kb upstream of the pituitary start site. The promoter does not react to dopamine, estrogens, or TRH. Instead, it is stimulated by cAMP. Responsiveness to cAMP is mediated by an imperfect cAMP–responsive element and two CAAT/enhancer binding proteins (C/EBP). Progesterone upregulates prolactin synthesis in the endometrium but decreases it in myometrium and breast glandular tissue. Breast and other tissues may express the Pit-1 promoter in addition to the distal promoter. Oct-1 appears able to substitute for Pit-1 in activating the promoter in breast cancer cells. Extrapituitary production of prolactin is thought to be special to humans and primates and may serve mostly tissue-specific paracrine and autocrine purposes. It has been hypothesized that in vertebrates such as mice a similar tissue-specific effect is achieved by a large family of prolactin-like proteins controlled by at least 26 paralogous PRL genes not present in primates.
Abraham White (March 8, 1908 – February 14, 1980) was a professor of biochemistry who made several important discoveries in his field during the middle of the 20th century and helped write a foundational textbook, Principles of Biochemistry, which was published in 1954. The book went through six editions before its authors retired. White was born in Cleveland, Ohio, to Morris and Lena White. His siblings were Essie and Julius ("Jay"). When he was about one year old, his family moved to Lafayette, Colorado, and then later to Denver. White earned his bachelor's and master's degrees at the University of Colorado and a Ph.D. degree in Physiological Chemistry at the University of Michigan in the laboratory of Howard B. Lewis. This was followed by a postdoctoral fellowship at the Yale School of Medicine with Hubert Bradford Vickery at the Connecticut Agricultural Experiment Station.
The use of high-resolution ion-mobility mass spectrometry (IMS-MS) on HPLC-purified alpha-synuclein in vitro has shown alpha-synuclein to be autoproteolytic (self-proteolytic), generating a variety of small molecular weight fragments upon incubation. The 14.46 kDa protein was found to generate numerous smaller fragments, including 12.16 kDa (amino acids 14–133) and 10.44 kDa (40–140) fragments formed through C- and N-terminal truncation and a 7.27 kDa C-terminal fragment (72–140). The 7.27 kDa fragment, which contains the majority of the NAC region, aggregated considerably faster than full-length alpha-synuclein. It is possible that these autoproteolytic products play a role as intermediates or cofactors in the aggregation of alpha-synuclein in vivo.
Sources: en.wikipedia.org
System suitability is typically performed before each batch or according to the validated method and laboratory procedure. Some long runs include periodic checks during analysis. The required frequency depends on regulatory expectations and method performance.
Retention time drift can result from changes in mobile phase composition, column temperature, pump flow, or column age. A gradual shift often points to column degradation. A sudden shift may indicate a leak, mixing error, or incorrect mobile phase.
Retention time alone cannot confirm identity because different compounds may elute at similar times. Coupling HPLC with mass spectrometry or comparing against authenticated standards increases confidence. Confirmation usually requires orthogonal data.
It measures the presence and amount of one or more compounds in a liquid sample. Separation occurs in a column, and detection produces a signal proportional to concentration. Identification usually requires comparison with a known reference standard under the same conditions.